Cisco Catalyst 9130AX Series
On Order Only
| Software | Catalyst 9130AXI Cisco Unified Wireless Network Software Release 8.10.x or later Cisco IOS ® XE Software Release 16.12.1 with AP Device Pack, or later |
| Supported wireless LAN controllers | Cisco Catalyst 9800 Series Wireless Controllers Cisco 3504, 5520, and 8540 Wireless Controllers and Cisco Virtual Wireless Controller |
| 802.11n version 2.0 (and related) capabilities | 4×4 MIMO with four spatial streams Maximal Ratio Combining (MRC) 802.11n and 802.11a/g 20- and 40-MHz channels PHY data rates up to 1.5 Gbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive) 802.11 Dynamic Frequency Selection (DFS) Cyclic Shift Diversity (CSD) support |
| 802.11ac | 8×8 downlink MU-MIMO with eight spatial streams MRC 802.11ac beamforming 20-, 40-, 80-, and 160-MHz channels PHY data rates up to 6.9 Gbps (160 MHz with 5 GHz) Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) 802.11 DFS CSD support WPA3 support |
| 802.11ax | 8×8 uplink/downlink MU-MIMO with eight spatial streams Uplink/downlink OFDMA TWT BSS coloring MRC 802.11ax beamforming 20-, 40-, 80-, and 160-MHz channels PHY data rates up to 10 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz) Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) 802.11 DFS CSD support WPA3 support |
| Integrated antenna | 2.4 GHz: Peak gain 4 dBi, internal antenna, omnidirectional in azimuth 5 GHz: Peak gain 6 dBi, internal antenna, omnidirectional in azimuth |
| External antenna with Smart antenna connector | The Cisco Catalyst 9130AXE Access Point is certified for use with antenna gains up to 13 dBi (2.4 GHz and 5 GHz) Cisco offers the industry’s broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios Supports Self-Identifiable Antennas (SIA) on the Smart antenna connector Smart antenna connector is a compact multi-RF connector with 8-DART interface Requires the AIR-CAB002-D8-R= 2-fppt smart antenna connector when used with antennas with a RP-TNC connector Requires the AIR-CAB003-D8-N= 3 ft smart antenna connector when used with AIR-ANT2513P4M-N= antenna |
| Interfaces | 1x 100, 1000, 2500, 5000 Multigigabit Ethernet (RJ-45) – IEEE 802.3bz Management console port (RJ-45) USB 2.0 at 4.5W (enabled via future software) |
| Indicators | Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors |
| Dimensions (W x L x H) | Access point (without mounting brackets): – C9130AXI: 8.9 x 8.9 x 1.88 in. (22.6 x 22.6 x 4.8 cm) |
| Environmental | Cisco Catalyst 9130AXI Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) Nonoperating (storage) altitude test: 25˚C, 15,000 ft (4600 m) Operating temperature: 32° to 122°F (0° to 50°C) Operating humidity: 10% to 90% (noncondensing) Operating altitude test: 40˚C, 9843 ft (3000 m) Note: When the ambient operating temperature exceeds 40°C, the access point will shift from 8×8 to 4×4 on the 5 GHz radio, uplink Ethernet will downgrade to 1 Gigabit Ethernet; however, the USB interface will remain enabled. |
| System memory | 2048 MB DRAM 1024 MB flash |
| Warranty | Limited lifetime hardware warranty |
| Available transmit power settings | 2.4 GHz 23 dBm (200 mW) 20 dBm (100 mW) 17 dBm (50 mW) 14 dBm (25 mW) 11 dBm (12.5 mW) 8 dBm (6.25 mW) 5 dBm (3.13 mW) 2 dBm (1.56 mW) -1 dBm (0.79 mW) -4 dBm(0.39 mW) 5 GHz 26 dBm (400 mW) 23 dBm (200 mW) 20 dBm (100 mW) 17 dBm (50 mW) 14 dBm (25 mW) 11 dBm (12.5 mW) 8 dBm (6.25 mW) 5 dBm (3.13 mW) 2 dBm (1.56 mW) -1 dBm (0.79 mW) |
| Maximum number of nonoverlapping channels | 2.4 GHz 802.11b/g: – 20 MHz: 3 802.11n: – 20 MHz: 3 802.11ax: – 20 MHz: 3 5 GHz 802.11a: – 20 MHz: 26 FCC, 16 EU 802.11n: – 20 MHz: 26 FCC, 16 EU – 40 MHz: 12 FCC, 7 EU 802.11ac/ax: – 20 MHz: 26 FCC, 16 EU – 40 MHz: 12 FCC, 7 EU – 80 MHz: 5 FCC, 3 EU – 160 MHz 2 FCC, 1 EU Note: This varies by regulatory domain. Refer to the product documentation for specific details for each regulatory domain. |
| Compliance standards | Safety: – IEC 60950-1 – EN 60950-1 – UL 60950-1 – CAN/CSA-C22.2 No. 60950-1 – AS/NZS60950.1 – UL 2043 – Class III equipment Emissions: – CISPR 32 (rev. 2015) – EN 55032 (rev. 2012/AC:2013) – EN 55032 (rev. 2015) – EN61000-3-2 (rev. 2014) – EN61000-3-3 (rev. 2013) – KN61000-3-2 – KN61000-3-3 – AS/NZS CISPR 32 Class B (rev. 2015) – 47 CFR FCC Part 15B – ICES-003 (rev. 2016 Issue 6, Class B) – VCCI-CISPR 32 – CNS (rev. 13438) – KN-32 – QCVN 118:2018/BTTTT Immunity: – CISPR 24 (rev. 2010) – EN 55024 + AMD 1(rev. 2010) – EN 55035: 2017 – KN35 Emissions and immunity: – EN 301 489-1 (v2.1.1 2017-02) – EN 301 489-17 (v3.1.1 2017-02) – QCVN (18:2014) – QCVN 112:2017/BTTTT – KN 489-1 – KN 489-17 – EN 60601-1-2:2015 – EN 61000-6-1: 2007 Radio: – EN 300 328 (v2.1.1) – EN 301 893 (v2.1.1) – AS/NZS 4268 (rev. 2017) – 47 CFR FCC Part 15C, 15.247, 15.407 – RSP-100 – RSS-GEN – RSS-247 – China regulations SRRC – LP0002 (rev 2018.1.10) – Japan Std. 33a, Std. 66, and Std. 71 RF safety: – EN 50385 (rev. Aug 2002) – ARPANSA – AS/NZS 2772 (rev. 2016) – EN 62209-1 (rev. 2016) – EN 62209-2 (rev. 2010) – 47 CFR Part 1.1310 and 2.1091 – RSS-102 IEEE standards: – IEEE 802.3 – IEEE 802.3ab – IEEE 802.3af/at – IEEE 802.11a/b/g/n/ac/ax – IEEE 802.11h, 802.11d Security: – 802.11i, Wi-Fi Protected Access 2 (WPA2), WPA3 – 802.1X – Advanced Encryption Standard (AES) Extensible Authentication Protocol (EAP) types: – EAP-Transport Layer Security (TLS) – EAP-Tunneled TLS (TTLS) or Microsoft Challenge Handshake Authentication Protocol (MSCHAP) v2 – Protected EAP (PEAP) v0 or EAP-MSCHAP v2 – EAP-Flexible Authentication via Secure Tunneling (EAP-FAST) – PEAP v1 or EAP-Generic Token Card (GTC) – EAP-Subscriber Identity Module (SIM) |
